Translucent & Tinted Exterior Joinery CoatingsA range of high performance waterborne joinery coatings with ISO9001 accreditation. Morrells offer technical support with product demonstrations, and specification writing. Please consult our Practical Guide to Joinery Finishing for additional information. EIMW4400Waterborne Clear Wood Treatment with excellent substrate penetration; for spray, flow-coating or dip application. Formulated to provide surface protection against fungal attack for exterior joinery such as doors, window frames, cladding, fascias and soffits. Must be tinted with EPTW series Waterborne Tinters when used as part of a translucent system. Application of 1 wet coat sufficient for optimum protection. Touch dry after 1 hour and overcoatable after 3 hours. Conforms to EN152-1/88 performance specification for fungal protection. EPTW SeriesConcentrated Waterborne Tinters for colouring EIMW 4400, EFWE 600, EOWE 550 & EOWE 560. EFWE600Waterborne Clear Sanding Sealer with excellent filling and sanding properties; for spray or brush application. Formulated to provide a fast drying, high clarity basecoat for exterior joinery such as doors, window frames, cladding, fascias and soffits. Application of 1 coat, to approximately 150 microns wet, over timber pre-treated with EIMW 4400 will provide a sufficient base coating. Touch dry after 1 hour, overcoating after 3 hours and stackable after 12 hours. EFWE700Solventborne Sealer with excellent filling and sanding properties; for spray or brush application. Formulated to provide a high clarity basecoat for timbers rich in tannins, natural oils and resins. EFIW3702 pack Waterborne Clear Barriercoat with excellent substrate adhesion and stain isolation; for spray application. Formulated to provide a stain isolating basecoat for tropical hardwoods and other timbers rich in tannin and natural extractives. Catalysed with ECW1 Activator. Application of 1 coat, to approximately 100 microns wet, over timber pre-treated with EIMW 4400 will provide a sufficient barrier coat. Touch dry after 1 hour, overcoating after 4 hours. EOWE550Waterborne Translucent Topcoat with excellent weathering resistance; for spray or brush application. Formulated to provide a fast drying, water resistant finish for exterior joinery such as doors, window frames, cladding, fascias and soffits. Application of 2 full coats, to approximately 300 microns wet, over timber pre-treated with EIMW 4400 will give full protection. Touch dry after 90 minutes, overcoating after 4 hours and stackable after 12 hours. Available in 30% or 60% sheen levels. Conforms to ENV 927-2/2000 performance specification. EOWE560Waterborne Translucent Topcoat formulated to provide a cleaner colour on light timbers such as Pine and Oak. Application of 2 full coats, to approximately 300 microns wet, over timber pre-treated with EIMW 4400 will give full protection. Touch dry after 90 minutes, overcoating after 4 hours and stackable after 12 hours. Available in 30% or 60% sheen levels. EOWE1Wax Based Finishing Oil for maintenance of pre-coated timber; for brush, rag or wiper application. Formulated to provide a high clarity water repellent finish for exterior joinery such as doors, window frames, cladding, fascias and soffits. Application of 1 coat will provide a sufficient finish. Touch dry after 4 hour and fully dry after 8 hours. Please download the SDS & PDS sheets from link at the bottom of this page. Exterior Joinery GuideDownload a practical guide for processing and coating wooden windows, doors, conservatories and wooden buildings. Download Guide to Joinery Finishing
Downloads |
Legals |Terms & Conditions | © 2008 Copyright Morrells Woodfinishes. All Rights Reserved.